| Home | E-Submission | Sitemap | Contact Us |  
Environ Eng Res > Volume 22(3); 2017 > Article
Sharma and Yadav: Bioconversion of flowers waste: Composting using dry leaves as bulking agent

Abstract

At present, in India, handling of solid waste has become a major challenge for the municipal authorities. Composting of solid waste, especially organic waste, can be one of the solutions to tackle the issue of handling solid waste. The present study is focused on agitated piles composting of flower waste (FW). Five combinations of FW with dry leaves (DL) and cow dung (CD) were prepared to conduct the study. Significant changes were observed due to the addition of bulking agent. The bulking material helps to reduce the production of leachate and also to maintain the aerobic condition within the piles. The reduction of total organic carbon was 21% in FW composting which increased by 36.48% during the composting of FW on addition of DL and CD. On the 120th day of composting, the pH of pile five (70 kg FW + 20 kg CD + 15 kg DL) was 7.33, electrical conductivity 2.77 mS/cm, total organic carbon 26.9%, total nitrogen 2.2%, and C:N ratio was 12. Appropriate proportion of waste mixture played an important role in providing favorable conditions for the microbial transformation of flower waste to stabilized compost. Finally, FW with the combination of CD and DL was found to be successful during pile composting.

1. Introduction

The generation of municipal solid waste is increasing day by day and its safe disposal is a challenge for the municipal authorities. Mobilization of people from rural and urban areas and the change in their lifestyle are the main reasons for increase in the quantity of solid waste in urban areas [1]. The present study was conducted in Surat, Gujarat (India). Surat is situated on the bank of the river Tapti. It is located at 21.17° north latitude and 72.83° east longitude. Flower waste (FW) falls under the category of municipal solid waste. The city of Surat generates around 1,700 MT of solid waste per day [2]. Among this, the quantity of flower waste is approximately 1.5–2 MT per day. India has a variety of cultural heritage and uses flowers for decoration purposes as well as for worship in holy places and as an offering to deities. Later these flowers are thrown away as waste material. Most of the time there flowers are mixed with municipal solid waste or allowed to decay naturally. They are also at times dumped into nearby water bodies thereby leading to water as well as environmental pollution. The FW thrown into water bodies, affects the aquatic life. This might lead to the outbreak of several epidemics.
Composting is a well-known and widely used method for converting organic waste into a nutrient enriched soil product [3, 4]. Composting is the biological decomposition and stabilization of organic substrates that allows development of thermophilic temperatures as a result of biologically produced heat [5]. The end product produced is stable. It is free of pathogens, and plant seeds, and can be beneficially applied to land. These organic fertilizers are eco-friendly and do not damage natural resources. Instead they improve the fertility of the soil resulting in healthy plants. Additionally, the levels of soil organic matter, soil microbial biomass and activities are enhanced by using organic fertilizers [6].
In the composting process, bulking agents play an important role in the degradation of organic matter. It acts as a buffer and helps to maintain the pH within the range (6 to 8) when organic acids are produced at the initial stage of the composting process [5, 7]. Bulking agents help to maintain aerobic conditions and moisture content within the limit (50–60%) into the piles during the process of degradation. The presence of excessive moisture will produce leachate and the composting process slows down due to reduction of oxygen availability and porosity. Bulking agents such as dry leaves (DL), rice husk, saw dust, etc. provide free air passage, porosity and avoid the formation of leachate. They also help to keep the whole waste mixture moist and sustain an active microbial activity [8]. Sufficient quantities of DL are available in spring and summer season which can be stored and used as a bulking agent for the composting of FW. Various authors used DL as bulking agent and concluded that DL can easily absorb moisture content during the composting period [911]. Kalamdhad and Kazmi [9] used DL for the composting of vegetables waste during the rotary drum composting. Ch’ng et al. [10] used pineapple leaves for composting. The author concluded that high quality compost can be produced by co-composting pine apple leaves and chicken manure slurry. Thereby reducing environmental pollution that could result from poorly managed agricultural waste.
Much literature is available for the composting of organic waste with bulking material but there are only limited studies available on composting by using DL and FW. The present study is focused on FW composting coupled with the role of bulking agent. The study also evaluates physicochemical changes during the composting process.

2. Materials and Methods

The main materials used in the study were FW and cow dung (CD) with DL as bulking agent. Characteristics of each of the materials used are presented in Table 1. In this study, FW was collected from nearby temples in Surat. The quantity and composition of FW varies widely from location to location. The collected FW comprised of the flowers namely Marigold, Rose, Jasmine, and Lotus. In this study, only FW was used for composting without stems, roots and leaves. Before using these FWs for composting; the waste was segregated. Segregation was done to separate plastic, paper, thread and other waste materials. CD which was used as microbial inoculums was collected from a nearby dairy farm at Vesu in Surat. The CD was manually mixed with DL. CD contains enriched nutrients for microorganisms and enhances the degradation rate. DL were collected from SVNIT campus. The quantity and composition of leaves varies widely from location to location and depends upon the type of plant/tree. Chopping of material was done to bring down the particle size to 3–5 cm. The material was thoroughly mixed before being made into piles. DL were used as a bulking material to maintain the aerobic condition and arrest the leaching process of the FW during composting.

2.1. Methodology (Agitated Pile Composting)

The present study was conducted to monitor changes in the physico-chemical parameters by preparing five different combinations of heaps for 120 days. Waste combinations were formed into trapezoidal piles (size: length 2,100 mm, base width 350 mm, top width 100 mm, height 250 mm) having length to base width (L/W) ratio of 6 [12]. The composting heaps were compressed to maintain the (L/W) ratio of 6. The agitated piles contained 90 kg to 100 kg of different waste combinations and were manually turned on at intervals of 4 d and the samples were analyzed. Two replicates were prepared for each pile. The parameters were monitored every four days for 120 d. Initially all the piles were covered with plastic sheet for four days. The pile combinations used are shown below:
  • - Combination 1 (Pile 1): 100 kg FW

  • - Combination 2 (Pile 2): 70 kg FW + 20 kg CD

  • - Combination 3 (Pile 3): 70 kg FW + 20 kg CD + 5 kg DL

  • - Combination 4 (Pile 4): 70 kg FW + 20 kg CD + 10 kg DL

  • - Combination 5 (Pile 5): 70 kg FW + 20 kg CD + 15 kg DL

2.2. Parameters Monitored and Sampling Frequency

Temperature was monitored on a daily basis using a digital thermometer throughout the composting period. Four grab samples from different locations of each pile were collected after turning the piles. Water was added to maintain the moisture content (50–60%). Gravimetric method was used for determining the moisture content of the fresh sample. Electrical conductivity was determined by using pH and electrical conductivity meter. 10 g dried sieved sample was diluted to 100 mL distilled water (1:10 w/v) and kept for shaking in a rotary shaker for two hours. After two hours the sample was kept for half an hour for settling and then filtered through a whatman filter paper no 42. Fresh wet samples were used for the presence of CO2 evolution rate. The CO2 evolution rate was determined as described by Singh and Kalamdhad [12]. Total nitrogen present was determined by Kjeldahl method. The presence of ammoniacal nitrogen was determined by KCl extraction method followed by phenate method [13]. Volatile solids were determined by keeping the oven dried sieved sample in a muffle furnace for 550 ± 2°C for 2 h. The total organic carbon was calculated by dividing the volatile solids by 1.83 [14]. Heating digester (Velp scientifica DK 20) was used for digesting the 0.2 g sample, 10 mL H2SO4 and HClO4 mixture (5:1) at 300°C ± 5°C for two hours. The digested samples were used for the determination of total phosphorous using stannous chloride methods [14]. The concentrations of Na, K and Ca were determined by using flame photometer.

3. Results and Discussion

FW, CD and DL contain 78.25%, 73.47% and 2% moisture content, respectively. It was observed that the addition of bulking agents which is a source of carbonaceous and fibrous material helps to control excess moisture and create pore space. Singh and Kalamdhad [12] reported that the bulking agent regulates moisture content and provides free air passage. In control piles, lump formation was observed after six days which may be due to excess moisture content and lack of air passage between the particles. These lumps were converted into a hard mass after a week. Formation of leachate was also observed in combination 1 and 2 where the bulking material was not mixed. In the Combination 5 (70 kg FW + 20 kg CD + 15 kg DL), the moisture content at the beginning was 69.87% and it reduced to 50.75% within the next 12 days. It may be due to increase in the quantity of bulking agent (15 kg). Initially all the piles were covered with plastic sheets for four days. Covering of piles with plastic sheets helps in increasing the temperature inside the piles and reach the thermophilic phase in a day. The growth of fungus was observed during the first four days due to moisture and a stagnant condition. The rise in temperature inside the pile due to bacterial activity and the presence of moisture (water) converted this heat into vapour. Yadav et al. [15] reported that the vapour produced is responsible for the breakdown of tough organic material (lignin or tannin). Adequate growth of fungus was observed for 3–4 d in all piles. It was observed that fungus played an important role in the breakdown of lignin and tannin of organic matter. Turning of piles at interval of 4 d provides adequate oxygen to the piles and helps to reduce the pungent odour. It also causes a rise in temperature. Turning of piles also helps to reduce the moisture content by 2–4% [16]. After thorough mixing by the turning of heaps, the amount of moisture decreased and the temperature increased. This shows that composting processes was still proceeding very actively [17]. It was observed that in combinations 1 and 2 there was not much loss of moisture but in the piles 3, 4 and 5 due to the addition of DL the moisture content was low.

3.1. Variation of Temperature

Variation of temperature in the composting heap is an indication of the rate of degradation and the type of microbial biomass present during the composting process. Temperature was measured throughout the composting process at various locations of piles (top, middle and bottom). Turning of the piles at intervals of 4 d provides oxygen which helps to maintain the aerobic condition inside the piles and elevates temperature. The highest temperature was observed in combination 5 (T = 54.7°C). It may be due to the increased quantity of bulking agent (15 kg dry leaves). The thermophilic phase (5 d) was more compared to other combinations. In combinations 1 and 2 the thermophilic phase was observed initially for 3 and 2 days, respectively. During the composting periods, it was observed that all combinations were properly sanitized and had reached active maturation phase. All the combinations had reached the thermophilic phase within 2 days. The temperature remained above 55°C for a period of two days, satisfying the regularity requirement for the destruction of pathogens [18]. In this study, it was observed that all combinations had satisfied the above conditions. The Fig. 1 indicates that temperature reaches the three phases namely the mesosphilic phase, the thermophilic phase and the cooling phase.

3.2. Variation of pH and Electrical Conductivity (EC)

pH is the one of the important parameters which greatly influenced the composting process. The pH range between 6.0 to 7.5 was favorable for the growth of bacteria and the value of the pH between 5.5 to 8.0 was favorable for the growth of fungi [19]. Fates of pH in different combinations are shown in Fig. 2. More acidic pH (5.01) was observed in combination 1 and 2 which may be due to the absence of bulking agent. In combination 1 to 5 the initial pH were 5.23, 5.47, 5.20, 5.47, and 6.21, respectively which increased to 7.43, 7.88, 7.21, 7.42, and 7.33, respectively after 120 days. Increase in the pH level during composting was due to degradation of protein. Degradation of short-chained fatty acids could also contribute into an increase of pH level [20]. Turning of the piles increased the rate of aeration and decreased the CO2 evolution rate in the compost. This may cause to increase the pH [21]. Composting proceeds most efficiently at the thermophilic temperature when the pH is approximately 8 [1, 22]. After the completion of thermophilic stage, nitrification bacteria take over the process. Due to nitrification process, the pH decreased at the end of the composting period. The decrease in pH at the later stage of composting might have occurred due to the volatilization of ammoniacal nitrogen and released of H+ ion as a result of microbial nitrification process by nitrifying bacteria [22, 23].
EC is a very useful parameter to check the level of salinity in the compost. EC was also responsible for phytotoxicity effects and plants growth when compost was applied to soils [20]. High salinity level in the compost can damage roots, affect nutrient uptake, limit plant-available soil water, or cause seed germination to be inhibited [24]. Variation of EC has been shown in Fig. 2. It was observed that in combinations 1 and 2 the initial electrical conductivity was 5.44 and 4.87 mS/cm, respectively and finally rose up to 6.21 and 5.24 mS/cm, respectively. The main reason for the increase of EC was the variation of nutrients such as P, K, Na and Ca in compost. Their concentration increased gradually with time, which might contribute the increase in electrical conductivity of compost. In case of combination 3, 4 and 5 the initial electrical conductivity was 3.84, 3.78 and 3.5 mS/cm decreased up to 3.54, 2.98 and 2.77 mS/cm, respectively in the matured compost. During the later stage of the composting process, electrical conductivity was decreased due to the volatilization of ammonia and the precipitation of mineral salts [25]. The conversion of available salts into mineral salts was also the main reason for the decrease in electrical conductivity during the later phase of the composting process [26].

3.3. Variation of Total Organic Carbon (TOC)

Degradation of total organic carbon depends on the availability of easily digestible material such as cellulose and hemicellulose. The microorganisms utilized carbon as a source of energy and nitrogen for the building of the cell structures. During the degradation process of the compost, microbes utilized 60 to 70% of the carbon as CO2 and incorporated (immobilize) only 30% to 40% of the carbon into their body as cellular components [14, 27]. Around 30% of the available carbon was utilized by the micro-organisms as a source of energy. Thus the total organic carbon content is useful for estimating the age and the physical properties of the compost. Initially the total organic carbon in combinations 1 to 5 were 43.72, 44.55, 41.26, 41.64 and 42.37(%), respectively and finally it reduced to 34.49, 33.41, 27.02, 27.01 and 26.91(%), respectively after 120 d. Temporal variations and reductions in total organic carbon of all combinations have been shown in Fig. 3. Higher degradation (34% to 36%) was observed in combination 4 and 5 due to the presence of bulking agents. It shows the role of bulking agent in organic carbon degradation. During the composting process, CO2 is emitted from the composting mass as a metabolic end product. Thus, the content of organic carbon decreased as the decomposition progressed [1, 28].

3.4. Variation of CO2 Evolution Rate

CO2 evolution rate is an important parameter to check the maturity of the compost because concentration of CO2 was reduced with maturity. Composting is a biological phenomenon in which micro-organisms play an important role in the degradation of organic matter and its transformation into mineralized substances which is somewhat the same as those available in soils. The CO2 evolution rate observed in all the piles was more or less equal. The initial CO2 evolution rates were 25.32 to 26.38 (mg/gVS/d) which reduced to 0.01 (mg/gVS/d) in all the combinations after 120 d of composting. CO2 evolution rate indicates maturity of the compost [29]. Bulking agents also play an important role in degradation and ultimately affect the CO2 evolution rate. In this study, a decreasing trend of CO2 evolution was observed in combinations 3, 4 and 5. The CO2 evolution rates directly shows the biological aerobic respiration rates during the composting process. It also shows the activity of the microbes during the composting process as at the end CO2 is a byproduct of compounds. It was observed that during the maturity stage of composting process CO2 evolution rate decreased. During the early stages it was observed that all the piles had high CO2 evolution rate due to the high presence of biodegradable organic matter. The decrease in the rate of CO2 evolution with composting time is a result of the reduction in metabolic activity, due to the decrease of readily available carbon [30].

3.5. Total Nitrogen (TN) and Ammoniacal Nitrogen (NH4+-N) and Carbon to Nitrogen Ratio (C:N ratio)

Table 2 shows the variation of total nitrogen, ammoniacal nitrogen and C:N ratio during the composting periods. Decreasing trends of ammoniacal nitrogen were observed during the composting process. Ammonia was generated from decomposition of nitrogenous material, i.e., proteins and amino acids [31]. Initial ammoniacal nitrogen in combination 1 was 175.95 (mg/kg) which reduced to 64.04 (mg/kg) after 120 days of composting. In combination 2, the initial ammoniacal nitrogen was 190.1 (mg/kg) and at the end of the composting period it was 87.98 mg/kg. Similarly in combinations 3, 4 and 5; the initial ammoniacal nitrogen were 211.22, 231.75, 241.93 mg/kg which reduced to 88.78, 100.7 and 114.98 mg/kg, respectively. The ammoniacal nitrogen concentration decreased due to volatilization of ammonia, immobilization and assimilation of NH4+-N by the microorganisms and nitrification during the composting process. During the turning NH4+-N was released as ammonia, thereby reducing ammoniacal nitrogen. The range of ammoniacal nitrogen in matured compost as suggested by Makan and others [32], was below 400 mg/kg. In the present study the concentration was very low which satisfied the maturity of the compost.
The total nitrogen in combinations 1 to 5 during the composting period were 1.4, 1.5, 1.6, 1.6 and 1.8%, respectively which finally increased from 1.8% to 2.2%. Increasing trends of total nitrogen were observed during the active thermophilic phase. It was observed that during the biodegradation process the nitrogen content increased due to the mineralization of organic matter. The nitrogen content in the final compost depends on the amount of nitrogen and C:N ratio of the feed.
C:N ratio was used by various researchers as the indicator for maturity of compost [16, 33, 34]. The initial C:N ratio of pile 1 was 33 which reduced to 19 at the end of the composting period. The reduction in C:N ratio was due to the reduction of total organic carbon and increase of total nitrogen during the composting period. The initial C:N ratio of pile 2 to pile 5 was 31 to 28 and it decreased to 12 to 19 at the end of composting period. The reduction of C:N ratio was due to the usage of carbon as a source of energy by the microorganisms while nitrogen was used for building the cell structure by the different group of microbes [34, 35]. If the availability of C:N ratio is more, then the excess carbon tends to utilize nitrogen in soil to build cell protoplasm. C:N ratio ranging from 10 to 25 is sufficient for the compost maturity [12]. It was observed that in all the piles the C:N ratio was within the limit. Low C:N ratios releases the salts or nutrients present in the compost and helps in plant growth.

3.6. Variation of Nutrients (Phosphorous, Potassium, Sodium and Calcium)

The total phosphorous (g/kg) gradually increased due to the decomposition of organic matter during the composting period. The initial total phosphorous in the combinations 1 and 2 was 7.58 and 8.65 (g/kg), respectively which finally increased to 22.66 and 21.69 (g/kg), respectively. Similarly in the combinations 3, 4 and 5 containing DL as bulking agent the initial phosphorous were 10.88, 11.11 and 12.02 (g/kg), respectively which after 120 days increased to 21.70, 22.69 and 22.54 (g/kg), respectively. There was an increase in phosphorous during the composting period due to degradation of organic matter. The phosphorous in the organic matter is used by the microorganisms for body metabolism and also for the growth of plants. Phosphorous is used by plants in soluble forms (orthophosphate ion) especially hydrogen phosphate ion (HPO42−). The increase in phosphorous concentration at the time of composting might be due to the higher rate of carbon loss that occurs when organic matter is decomposed or mineralised into CO2 or CH4.
The initial concentration of potassium in combinations 1 to 5 were 17.30, 13.89, 13.55, 13.89 and 14.50 (g/kg), respectively which increased to 38.62, 31.06, 22.56, 22.66 and 23.95 (g/kg), respectively at the end of the composting period. The unique potassium behaviour in all the piles might have been partly due to potassium assimilation and immobilisation by microbes [35]. The concentration of potassium content was high in case of all the five combinations. It shows the high inherent content in FW, suggesting that compost can be a good source of potassium fertilizer.
The concentration of sodium and calcium gradually increased which also indicates the net loss in dry mass due to the degradation of organic matter and the release of CO2 mineralisation during the composting period. In combinations 1 to 5, the initial sodium was 1.48, 1.94, 2.59, 2.66 and 3.16 g/kg which increased to 5.94, 5.84, 5.14, 6.22 and 5.16 g/kg, respectively. Similarly in combinations 1 to 5 the initial calcium were 4.36, 4.52, 5.81, 6.32 and 6.44 g/kg, respectively which finally increased to 13.56, 15.56, 13.11, 16.52 and 17.02 g/kg, respectively. Calcium and sodium are useful nutrients for plant growth. When compost is mixed with soil it increases soil acidification and makes more nutrients available to the plant. Increasing trends were observed in all the combinations and it was due to the reduction of dry mass of organic carbon, nitrogen, hydrogen and oxygen. Many studies have also emphasized on the importance of Na, P, K and Ca to protect the plant from diseases, pests, drought and cold [36, 37]. The production of good quality manure is essential to improve the fertility of soil thereby yielding healthy plants.

4. Conclusions

FW is a good source of organic waste. The degradation of FW can be increased by using bulking agent (DL). Covering of piles with polythene sheets helps in fungal growth and increase in temperature which in turn helps to break down the tough organic content of the waste. The degradation of FW without bulking agents resulted in formation of lumps, which might be due to high moisture content but lack of bulking agents. Maximum quantity (15 kg) of bulking agent (DL) was added in the FW. 70 kg FW + 20 kg CD + 15 kg DL (combination 5) which resulted in rapid decrease of moisture content, total organic carbon (reduced to 36.48 %), final pH (reduced to 7.33), EC (reduced to 2.77 mS/cm) and C:N ratio (reduced to 12). The compost prepared from FW using DL was beneficially used as manure for the increase in rate of crop production. Increasing trends of sodium, potassium, calcium and phosphorous were observed after composting period 120 days.

References

1. Awasthi MK, Pandey AK, Khan J, Bundela PS, Wong JW, Selvam A. Evaluation of thermophilic fungal consortium for organic municipal solid waste composting. Bioresour Technol. 2014;168:214–221.
crossref pmid

2. Surat Municipal Corporation. Solid waste management [Internet]. c2009. [cited 2 October 2016]. Available from: http://www.suratminiciapl.gov.in/Home/Index/Departments/Helath/SolidwasteManagement/Approaches


3. Lim SL, Wu TY. Characterization of matured vermicompost derived from valorization of palm oil mill byproduct. J Agr Food Chem. 2016;64:1761–1769.
crossref

4. Wu TY, Lim SL, Lim PN, Shak KPY. Biotransformation of biodegradable solid wastes into organic fertilizers using composting or/and vermicomposting. Chem Eng Trans. 2014;39:1579–1584.


5. Li Z, Lu H, Ren L, He L. Experimental and modeling approaches for food waste composting: A review. Chemosphere. 2013;93:1247–1257.
crossref pmid

6. Lim SL, Wu TY, Lim PN, Shak KPY. The use of vermicompost in organic farming: Overview, effects on soil and economics. J Sci Food Agr. 2015a;95:1143–1156.
crossref

7. Ramdani N, Hamou A, Lousdad A, Al-Douri Y. Physicochemical characterization of sewage sludge and green waste for agricultural utilization. Environ Technol. 2014;36:1594–1604.
crossref

8. Villaseñor J, Rodriguez L, Fernandez F. Composting domestic sewage sludge with natural zeolite in a rotary drum reactor. Bioresour Technol. 2011;102:1447–1454.
crossref pmid

9. Kalamdhad AS, Kazmi AA. Rotary drum composting of different organic waste mixtures. Waste Manage Res. 2009;27:129–137.
crossref

10. Ch’ng HY, Ahmed OH, Kassim S, Ab Majid NM. Co-composting of pineapple leaves and chicken manure slurry. Int J Recycl Org Waste Agric. 2013;2:1–8.
crossref

11. Schwintzer CR, Tjepkema JD, Seekins B. Nitrogenase activity in composting horse bedding and leaves. Plant soil. 2002;242:277–282.
crossref

12. Singh J, Kalamdhad A. Effect of rotary drum on the specification of heavy metals during the water hyacinth composting. Environ Eng Res. 2013;18:177–189.
crossref pdf

13. APHA. Standard methods for the examination of water and wastewater. 21st edWashington D.C: American Public Health Association; 2005.


14. Adhikari BK, Barrington S, Martinez J, King S. Effectiveness of three bulking agents for food waste composting. Waste manage. 2009;29:197–203.
crossref

15. Yadav KD, Mistry N, Pandya D, Ganvit B. Composting of food and vegetable waste. IUP J Environ Sci. 2010;4:27–38.


16. Zhu N. Effect of low initial C/N ratio on aerobic composting of swine manure with rice straw. Bioresour Technol. 2007;98:9–13.
crossref pmid

17. Wani KA, Mamta , Rao RJ. Bioconversion of garden waste, kitchen waste and cow dung into value-added products using earthworm Eisenia fetida. Saudi J Biol Sci. 2013;20:149–154.
crossref pmid pmc

18. Himanen M, Hänninen K. Composting of bio-waste, aerobic and anaerobic sludges – Effect of feedstock on the process and quality of compost. Bioresour technol. 2011;102:2842–2852.
crossref pmid

19. Amir S, Hafidi M, Merlina G, Revel JC. Sequential extraction of heavy metals during composting of sewage sludge. Chemosphere. 2005;59:801–810.
crossref pmid

20. Lim PN, Wu TY, Clarke C, Daud NNN. A potential bio-conversion of empty fruit bunches into organic fertilizer using Eudrilus eugeniae. Int J Environ Sci Technol. 2015b;12:2533–2544.
crossref

21. Hu Z, Lane R, Wen Z. Composting clam processing wastes in a laboratory- and pilot-scale in-vessel system. Waste Manage. 2009;29:180–185.
crossref

22. Tognetti C, Laos F, Mazzarino M, Hernandez M. Composting vs. vermicomposting: A comparison of end product quality. Compost Sci Util. 2005;13:6–13.
crossref

23. Eklind Y, Kirchmann H. Composting and storage of organic household waste with different litter amendments. II: Nitrogen turnover and losses. Bioresour Technol. 2000;74:125–133.
crossref

24. Lim SL, Lee LH, Wu TY. Sustainability of using composting and vermicomposting technologies for organic solid waste biotransformation: Recent overview, greenhouse gases emissions and economic analysis. J Clean Prod. 2016;111:262–278.
crossref

25. Huang G, Wong J, Wu Q, Nagar B. Effect of C/N on composting of pig manure with sawdust. Waste Manage. 2004;24:805–813.
crossref

26. Wong JWC, Mak KF, Chan NW, et al. Co-composting of soybean residues and leaves in Hong Kong. Bioresour Technol. 2001;76:99–106.
crossref pmid

27. Yadav A, Garg V. Feasibility of nutrient recovery from industrial sludge by vermicomposting technology. J Hazard Mater. 2009;168:262–268.
crossref pmid

28. Kalamdhad AS, Kazmi A. Effects of C/N ratio on mixed organic waste composting in a rotary drum composter. Int J Environ Eng. 2009;1:187–207.
crossref

29. Varma VS, Kalamdhad A. Effect of leachate during vegetable waste composting using rotary drum composter. Environ Eng Res. 2014;19:67–73.
crossref pdf

30. Iqbal MK, Shafiq T, Ahmed K. Characterization of bulking agents and its effects on physical properties of compost. Bioresour Technol. 2010;101:1913–1919.
crossref pmid

31. Jiang J, Huang Y, Liu X, Huang H. The effects of apple pomace, bentonite and calcium superphosphate on swine manure aerobic composting. Waste manage. 2014;34:1595–1602.
crossref

32. Makan A, Assobhei O, Mountadar M. Effect of initial moisture content on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco. Iranian J Environ Health Sci Eng. 2013;10:3.
crossref pmid pmc

33. Vig AP, Singh J, Wani SH, Singh DS. Vermicomposting of tannery sludge mixed with cattle dung into valuable manure using earthworm Eisenia fetida (Savigny) . Bioresour Technol. 2011;102:7941–7945.
crossref pmid

34. Nguyen XP, Jho H, Jeong YJ, Jo YT, Islam MN, Park JH. Characterization of composted chicken manure discharged from farms in South Korea. Environ Eng Res. 2015;20:254–259.
crossref

35. Kalemelawa F, Nishihara E, Endo T, et al. An evaluation of aerobic and anaerobic composting of banana peels treated with different inoculums for soil nutrient replenishment. Bioresour Technol. 2012;126:375–382.
crossref pmid

36. Debosz K, Petersen SO, Kure LK, Ambus P. Evaluating effects of sewage sludge and household compost on soil physical, chemical and microbiological properties. Appl Soil Ecol. 2002;19:237–248.
crossref

37. Tsai SH, Liu CP, Yang SS. Microbial conversion of food wastes for biofertilizer production with thermophilic lipolytic microbes. Renew Energ. 2007;32:904–915.
crossref

Fig. 1
Variation of temperature during the composting period.
/upload/thumbnails/eer-22-3-237f1.gif
Fig. 2
Variation of pH and electrical conductivity during composting period.
/upload/thumbnails/eer-22-3-237f2.gif
Fig. 3
Variation of total organic carbon during composting period.
/upload/thumbnails/eer-22-3-237f3.gif
Fig. 4
Variation of CO2 evolution rate during composting period.
/upload/thumbnails/eer-22-3-237f4.gif
Fig. 5
Variation of phosphorous, potassium, sodium and calcium during composting period
/upload/thumbnails/eer-22-3-237f5.gif
Table 1
Initial Physico-Chemical Characteristics of Materials Used for Composting
Parameter Flower waste Cow dung Dry leaves
pH 6.76 ± 0.10 7.71 ± 0.10 6.4 ± 0.20
Electrical conductivity (mS/cm) 5.44 ± 0.20 4.50 ± 0.20 0.50 ± 0.10
Moisture content (%) 78.25 ± 2.00 73.47 ± 20 2.00 ± 0.50
Total organic carbon (%) 46.87 ± 1.00 47.97 ± 1.00 53.82 ± 1.50
Total Nitrogen (%) 1.40 ± 0.09 1.50 ± 0.06 1.80 ± 0.90
Ammonical nitrogen (%) 1.85 ± 0.08 0.39 ± 0.60 1.29 ± 0.09
Carbon to nitrogen ratio 33.47 ± 0.08 31.98 ± 0.04 29.90 ± 0.07
Sodium (g/kg) 1.47 ± 0.07 3.51 ± 0.20 4.25 ± 0.10
Potassium (g/kg) 17.30 ± 0.30 5.96 ± 0.20 2.45 ± 0.10
Calcium (g/kg) 4.01 ± 0.30 3.72 ± 0.20 1.25 ± 0.10
Phosphorous (g/kg) 3.18 ± 0.01 2.794 ± 0.03 2.217 ± 0.02
Table 2
Variation of Ammoniacal Nitrogen (mg/kg), Total Nitrogen (%) and C:N Ratio
Ammonical Nitrogen (mg/kg)

Days 100 kg FW 70 kg FW + 20 kg CD 70 kg FW + 20 kg CD + 5 kg DL 70 kg FW + 20 kg CD + 10 kg DL 70 kg FW + 20 kg CD + 15 kg DL
0 175.95 ± 0.81 190.1 ± 0.78 211.22 ± 1.21 231.75 ± 1.20 241.93 ± 1.09
30 118.87 ± 1.01 126.41 ± 0.57 147.84 ± 1.02 149.9 ± 0.87 170.79 ± 1.21
60 88.89 ± 0.75 119.78 ± 0.87 131.57 ± 0.87 140.53 ± 0.84 140.1 ± 0.97
90 77 ± 0.94 91.05 ± 0.81 114.91 ± 1.57 121.47 ± 0.89 124.91 ± 0.85
120 64.04 ± 1.11 87.98 ± 0.95 88.78 ± 1.87 100.77 ± 0.76 114.98 ± 0.88
Total Nitrogen (%)
0 1.4 ± 0.21 1.5 ± 0.22 1.6 ± 0.20 1.6 ± 0.28 1.5 ± 0.27
30 1.6 ± 0.31 1.6 ± 0.30 1.8 ± 0.16 1.8 ± 0.21 2.0 ± 0.14
60 1.6 ± 0.14 1.7 ± 0.17 1.9 ± 0.18 1.8 ± 0.18 2.1 ± 0.27
90 1.8 ± 0.24 1.8 ± 0.16 1.9 ± 0.15 1.9 ± 0.11 2.2 ± 0.30
120 1.8 ± 0.19 1.8 ± 0.12 1.9 ± 0.17 1.9 ± 0.14 2.2 ± 0.24
C:N ratio
0 33 ± 0.08 30 ± 1.51 28 ± 1.61 28 ± 0.87 31 ± 1.02
30 27 ± 0.97 26 ± 1.72 18 ± 0.84 18 ± 1.29 17 ± 0.87
60 24 ± 1.14 22 ± 0.78 15 ± 1.35 15 ± 1.27 15 ± 0.92
90 19 ± 0.87 20 ± 0.84 14 ± 0.95 14 ± 0.94 12 ± 1.32
120 19 ± 0.84 19 ± 1.38 14 ± 0.85 14 ± 0.86 12 ± 0.81
TOOLS
PDF Links  PDF Links
PubReader  PubReader
Full text via DOI  Full text via DOI
Download Citation  Download Citation
  Print
Share:      
METRICS
12
Web of Science
15
Crossref
0
Scopus
65,535
View
501
Download
Editorial Office
464 Cheongpa-ro, #726, Jung-gu, Seoul 04510, Republic of Korea
TEL : +82-2-383-9697   FAX : +82-2-383-9654   E-mail : eer@kosenv.or.kr

Copyright© Korean Society of Environmental Engineers.        Developed in M2PI
About |  Browse Articles |  Current Issue |  For Authors and Reviewers